Demo · sources listed
Comfortably Numb — outro solo
Pink Floyd (David Gilmour) · Comfortably Numb (The Wall, 1979) · Singing, sustained fuzz with huge space
Checked · 7 blocks · 53 settings
The catalog matches CorOS 4.1.1, compiled October 2026. On older firmware, a block can be missing.
The chain, in signal order
- Chief CS3 (Compressor, row 1, slot 1)
SUSTAIN 3.5, ATTACK 5, TONE 5, LEVEL 6
Stands in for the MXR Dynacomp on the 1979 boards (the catalog has no Dynacomp). Sustain is kept low, like Gilmourish's listed sensitivity of about 10 o'clock, so it evens out the clean part. It stays off for the fuzz solos.
- Fuzz Pi (Overdrive, row 1, slot 2)
SUSTAIN 7, TONE 4, VOLUME 6
The Big Muff Pi model, standing in for the Ram's Head Muff at the heart of the solo tone. Settings follow Gilmourish's Wall-era Muff settings (sustain 70%, tone 30-40%, volume 50-60%) and Kit Rae's tone sweet spot of 35-40%. Values shown are for the outro scenes.
- Watt D103 Bright (Amp, row 1, slot 3)
GAIN 4.5, BASS 4, MID 6, TREBLE 6, PRESENCE 4.5, MASTER 7, OUTPUT 0 dB
The Hiwatt DR103 model, his actual amp. It is set loud but still clean, so the Muff supplies the dirt and the amp adds the solid, singing sustain.
- 412 Brit TV GB75Hz ’69 (Cab, row 1, slot 4)
MIC Dynamic 57, POSITION 3, DISTANCE 1.5, LEVEL 0 dB, HPF 80 Hz, LPF 7000 Hz
The catalog has no WEM Starfinder/Fane Crescendo 4x12, so this vintage British 4x12 with G12M25s is the closest match. The SM57 sits just off the cap, and the 7 kHz LPF tames the fuzz fizz.
- Rotary (Modulation, row 2, slot 5)
SPEED Slow, SLOW SPEED 1.2 Hz, FAST SPEED 6 Hz, ACCELERATION 40%, SPEAKER BALANCE 0%, DRIVE 15%, BRIGHTNESS 60%, HORN MIC WIDTH 80%, SYNC Off
Approximates the separately miked Yamaha RA-200 rotating speakers that ran in parallel with the Hiwatts. The block has no MIX control, so it sits on Path B and the Mixer blends it under the dry amp.
- Dual Delay (Delay, row 1, slot 6)
MIX 25%, SYNC L Off, DELAY TIME L 580 ms, FEEDBACK L 40%, SYNC R Off, DELAY TIME R 580 ms, FEEDBACK R 40%, X-FEEDBACK 0%, LINK FBACK Off, HIGH PASS 150 Hz, LOW PASS 5000 Hz, MOD RATE 0.3 Hz, MOD DEPTH 5%, DYN MODE Off, TRAILS On
A stereo delay that keeps the rotary's width, standing in for the MXR Digital Delay System I. The rolled-off top gives the darker, analog-type repeats Kit Rae suggests. Its independent L/R sides allow his measured two-tap intro/verse delay. Values shown are for early-outro Scene C: 580 ms with 4-5 repeats.
- Plate (Reverb, row 1, slot 7)
MIX 18%, DECAY 40%, PRE DELAY 25 ms, HIGH PASS 200 Hz, LOW PASS 6000 Hz, LF DAMPING 40%, HF DAMPING 40%, MOD DEPTH 15%, TRAILS On
Adds the studio-mix ambience behind the solo. No reverb unit is documented for this track, so a filtered plate stands in for late-70s studio plates.
Scenes
- Scene A · Clean (Intro/Verse) CS3 on, Fuzz Pi bypassed, rotary blended low (Mixer LEVEL B -9 dB). Dual Delay uses Kit Rae's studio intro/verse taps: a single repeat on the left and two repeats on the right. Kit also hears a second single L repeat at about 1850 ms, which this block cannot add. The amp OUTPUT is raised so the clean part matches the fuzz scenes. Bridge pickup (Gilmourish lists it for the studio rhythm part), or neck/middle for a softer clean. Changes: Watt D103 Bright OUTPUT 2 dB; Dual Delay MIX 18%, DELAY TIME L 650 ms, FEEDBACK L 5%, DELAY TIME R 1400 ms, FEEDBACK R 20%; Plate MIX 15%. Bypassed: Fuzz Pi.
- Scene B · Solo 1 CS3 off, Fuzz Pi on. Dual Delay gives 4-5 repeats. Bridge pickup; for warmer notes, try neck/middle or roll the tone back. Changes: Fuzz Pi SUSTAIN 6.5, TONE 3.5; Dual Delay MIX 20%, DELAY TIME L 450 ms, DELAY TIME R 450 ms; Plate MIX 15%. Bypassed: Chief CS3.
- Scene C · Outro Solo (early) CS3 off, Fuzz Pi hotter (SUSTAIN 7, TONE 4, VOLUME 6). Dual Delay L/R 580 ms, FEEDBACK L/R 40%, MIX 25%, matching Kit Rae's measurement for the first part of the outro. Plate MIX 18%. Bridge pickup for bite on the fast bends, finger vibrato and pinch harmonics. Bypassed: Chief CS3.
- Scene D · Outro Solo (late) Same as Scene C, but the Dual Delay drops to the shorter time, following Kit Rae's note that the outro delay shortens to about 450 ms later in the solo. Switch to it partway through the outro. Changes: Dual Delay DELAY TIME L 450 ms, DELAY TIME R 450 ms. Bypassed: Chief CS3.
Rig story
- Original rig
- Kit Rae, Gilmourish and Guitar.com all describe the same rig: the Black Strat (DiMarzio FS-1 bridge pickup) into a Ram's Head Big Muff, then split. One side went to two 100W Hiwatt DR103 heads into WEM Super Starfinder 4x12s with Fane Crescendo speakers. The other went through an Alembic F-2B preamp into two Yamaha RA-200 rotating speakers. Each side was miked separately, and the 1979 board had an MXR Digital Delay System I. Gilmour has said he played five or six takes of the outro solo and built the final one from the best phrases by riding faders (Wikipedia credits James Guthrie with assembling it). Bob Ezrin recalls the first solo as essentially a first take. Whether a booster was used is disputed: Gilmourish and Guitar.com list a Pete Cornish ST-2 Treble & Bass Booster on the studio board, Reverb points to a Colorsound Power Boost, and Kit Rae thinks there was none. The delay times below are Kit Rae's by-ear measurements, not documented settings.
- Instrument
- A Strat with a hot bridge single-coil. The Black Strat had a DiMarzio FS-1 for the 1979 sessions; an SSL-1/SSL-5-type is a close modern stand-in. Use the bridge pickup for both solos. Gilmourish lists the bridge pickup for both the studio rhythm part and the live solo. Kit Rae hears some neck-pickup warmth in solo 1, but the neck+bridge mini-toggle theory is unconfirmed: by Kit Rae's account, Gilmour said he wasn't sure he ever recorded with it. For those warmer moments, try neck/middle (position 4) or roll back the tone knob. For the clean scene, use the bridge pickup, or neck/middle for a softer sound.
- Routing
- Row 1: In 1 > Chief CS3 (slot 1) > Fuzz Pi (2) > Watt D103 Bright (3) > 412 Brit TV GB75Hz ’69 cab (4). A Splitter after slot 4 uses TYPE A/B with LEVEL TO A and LEVEL TO B at unity; the Balance type lowers the level of both paths. Path A (Row 1, slot 5 left empty) carries the dry amp/cab signal. Path B (Row 2, slot 5) carries the Rotary. The Mixer after slot 5 is set to LEVEL A 0 dB, LEVEL B about -9 dB, PAN A/B centred and PHASE off. Then Dual Delay (Row 1, slot 6) > Plate (slot 7) > Multi Out, with slot 8 free. On the original rig the split came before the amps: the Muff fed the Hiwatts, and an Alembic F-2B preamp fed the RA-200s. Here the rotary takes the post-cab signal, so the fuzz is already speaker-filtered when it reaches the rotary.
Tips
- Do not max the Fuzz Pi SUSTAIN. Gilmourish lists the Wall Muff at sustain 70%, tone 30-40% and volume 50-60%. Kit Rae puts the tone sweet spot at 35-40% from zero. The Hiwatt's clean headroom keeps the notes defined, so keep the amp loud and clean.
- Leave delay SYNC off. Song databases list the track at 127 BPM, which feels like a 64 BPM half-time. At 64 BPM an eighth note is about 469 ms and a dotted eighth about 703 ms. Kit Rae's 450 ms sits near the eighth, but 580 ms sits on no grid value, and a dotted-eighth setting is not what was used. His song page hears about 480 ms with only 2-3 repeats on the isolated track, so if the tails feel too long, drop FEEDBACK to about 30%.
- Use the Input block's INPUT GATE (tap-and-hold In 1) at a gentle threshold instead of a gate block, so the delay and plate tails don't get cut off between phrases.
- If the rotary wobble is too obvious, lower Mixer LEVEL B to about -12 dB rather than slowing the rotor. The original RA-200s were miked separately and mixed in stereo, so try PAN A slightly left and PAN B slightly right for more width.
- For a darker, more Fane-like top end, swap the cab's Dynamic 57 for the Ribbon 160, or pull the cab LPF down to about 6 kHz.
- Sources disagree on a booster. Gilmourish and Guitar.com list a Pete Cornish ST-2 on the 1979 studio board, Reverb points to a Colorsound Power Boost, and Kit Rae thinks none was used. To try one, put an Exotic Z Boost (GAIN about 6, VOLUME near unity) before the Fuzz Pi and drop SUSTAIN to about 4.5, which mirrors Kit Rae's Colorsound-into-Muff test. Bypass it in Scene A.
- Kit Rae suspects an 18V Electric Mistress on the outro solo; Gilmourish lists Big Muff, Electric Mistress and delay for live versions. To test it, insert an MX Flanger after the Fuzz Pi (shift the chain right one slot; Row 1 has room). Use subtle settings: MIX about 30%, SPEED about 15%, REGEN about 30%, active only in Scenes C and D.
- Set the Watt D103 OUTPUT per scene to match levels between the clean and fuzz scenes. Rolling the guitar volume to about 8 on the fuzz scenes tightens the low end.
Sources
- http://www.kitrae.net/music/Music_mp3_Comfortably_Numb_Sound.html
- https://www.kitrae.net/music/David_Gilmour_Delay%20Time%20Library.html
- https://www.gilmourish.com/?page_id=20
- https://www.gilmourish.com/?page_id=50
- https://www.gilmourish.com/?page_id=79
- https://guitar.com/features/artist-rigs/the-gear-used-by-david-gilmour-pink-floyd-the-wall/
- https://www.guitarworld.com/news/pink-floyds-david-gilmour-talks-comfortably-numb-solo-covers-tina-s-richie-faulkner-and-thomas-leeb
- https://www.guitarworld.com/news/pink-floyd-comfortably-numb-solo-controversy
- https://www.guitarworld.com/features/the-secrets-behind-david-gilmours-tone-on-pink-floyds-comfortably-numb
- https://en.wikipedia.org/wiki/Comfortably_Numb
- https://reverb.com/news/how-to-nail-gilmours-comfortably-numb-solo
- https://songbpm.com/@pink-floyd/comfortably-numb
- https://neuraldsp.com/manual/quad-cortex
- https://unity.neuraldsp.com/t/volume-perception-with-splitter/13853
This is a starting point. Your guitar, pickups and headphones or speakers change the sound, so adjust by ear from here.
© 2026 Gridtone, made by Loïc Sans, loicsans.me. QC-style grid. Gridtone is independent and not affiliated with Neural DSP or Anthropic.